PDA

View Full Version : Easy Homemade Sinkbridge



Paradox
03-07-2013, 07:18 PM
I posted this on another forum and thought it might be interesing here too.

I make raised bed gardens out of cedar decking material. It was pretty easy to make my own sinkbridge with some left overs from my work. The cedar is really good for this because it handles being wet very well. No mold or rot to speak of and it doesn't warp to any degree that would interfere with being used a sink bridge.

Measure your sink, and cut a board to size. Then cut a couple of blocks to attach for keeping the bridge in place. With the board on the sink just hold one of the blocks against one side of the sink. Then holding them together for fit just pull it away and attach the block. Then repeat for the other end. I like using a 6 inch board but a 4 inch wide one will do fine too. Use what you have around if you can I say.

http://i254.photobucket.com/albums/hh99/sjw800/sbridge01_zpsb9a8da99.jpg
Sinkbridge ready to be used.

http://i254.photobucket.com/albums/hh99/sjw800/sbridge02_zpsc476dd06.jpg
See the blocks? Install them to fit to your sink and keep the bridge from moving on you.

http://i254.photobucket.com/albums/hh99/sjw800/sbridge03_zps562c12c8.jpg
Attach the blocks with a couple of screws.
I sanded the edges and corners on mine a little to make sure there are no splinters.

http://i254.photobucket.com/albums/hh99/sjw800/sbridge04_zpsb59c119c.jpg
Not a must but a damp washcloth or disposable towel between the bridge and stone will keep it steady.
A "handywipe" type of "semi-disposable" towel really works well.

bathonuk
03-07-2013, 07:53 PM
I am using only the board. Instead of blocks holding the bridge I'm using non slip pads and it works great. It is a good idea to drill some holes in the board so water and swarf will go back to the sink.

http://lh4.ggpht.com/-Q-afD_XeM3g/UTkk7cuxWtI/AAAAAAAAMv0/8qxtD4fkUPM/s1024/20130307_232922.jpg (https://picasaweb.google.com/105172329006238409782/SinkBridge#5852749794487917266)
http://lh5.ggpht.com/-bA-hb_0_HXc/UTkk_y5wZ4I/AAAAAAAAMwQ/oHfNdhQInjk/s1024/20130307_232937.jpg (https://picasaweb.google.com/105172329006238409782/SinkBridge#5852749869159049090)
http://lh3.ggpht.com/-uU81b5ejW3c/UTklE7w6xtI/AAAAAAAAMwE/hhoFbsr8Q6w/s1024/20130307_232949.jpg (https://picasaweb.google.com/105172329006238409782/SinkBridge#5852749957437245138)

scotchef38
03-08-2013, 04:57 AM
Thats exactly what i use,but i didnt think about drilling holes for drainage.cheers

apicius9
03-08-2013, 05:19 AM
Mmhh, does that come in koa? ;) Great idea, the problem I run into is the work height. I am just 6' but bent over the sink for more than a few minutes, my back feels like it will break any moment... Still looking for a solution with clean water access, may have to build something more elaborate. Or try a bar stool.

Stefan

pete84
03-08-2013, 06:54 AM
I need to make one of those, now to find some scrap wood...

cwrightthruya
03-08-2013, 10:08 AM
Check out mine from this thread. I am also 6 feet and had the same problem, but I used a pair of 1x6 poplar boards glued together, along with a a set of risers, to give me the height. It sits beautifully and is very stable. What you can't see from the picture is a strip of wood running the length of the bridge which acts to hold it in place.
http://www.kitchenknifeforums.com/showthread.php/10066-Lets-see-your-sharpening-stations/page5

Regards,
Chris


Mmhh, does that come in koa? ;) Great idea, the problem I run into is the work height. I am just 6' but bent over the sink for more than a few minutes, my back feels like it will break any moment... Still looking for a solution with clean water access, may have to build something more elaborate. Or try a bar stool.

Stefan