View Full Version : Keeping an even bevel from tip to heel
11-12-2012, 03:49 PM
I'm relatively new to sharpening and so far have had some decent results. I own 3 stones (500,1k and 6k) and a DMT extra coarse. One of my biggest challenges is keeping the bevel edge even from tip to heel. The tip to the belly is always spot on but about 3/4 down the knife towards the heel the bevel tends to get slightly uneven. I figured this was due to mainly technique and practice but regardless of angle it seems that this particular area of the knife the bevel slightly becomes uneven. Is there something I'm missing here? Is there a way to blend the top edge of the bevel into the knife better (maybe using a de-buring block with chromium oxide) to make it look more alined? Or am I simply doing it wrong. It's not horrendously uneven but enough to bother me and to post this. Any feedback is much appreciated.
11-12-2012, 03:51 PM
Is this on one knife or does the same issue come up on multiple blades?
11-12-2012, 03:54 PM
Welcome to the forum!
11-12-2012, 03:58 PM
One so far-Misono togiharu 440 Pro-wondering if it's the actual shape of the knife? You can really notice it if holding the blade and staring down the bevel from heel to tip.
Thanks! glad to be here
11-12-2012, 04:19 PM
I'm really baffled by this-not sure how the same angle consistently on a stone could produce such an effect. The stones are flattened before each sharpening session an the knife stays at the same angle. It's a wave effect but only is happening around the heel of the knife
11-12-2012, 04:26 PM
The link refers to a local address I'm afraid. Could you use an image host, like postimage.org instead?
11-12-2012, 04:32 PM
Only getting the wave effect near the heel of the blade-tip to bevel is near perfect.
11-12-2012, 04:57 PM
I wish mine was that good!
11-12-2012, 05:12 PM
Unless you are pressing very hard on the corners of the stone, this is just due to the grind on the knife. Flash a light across the blade face and see if you notice the light plays off it differently at those spots. It should be high where the bevel gets thicker and low where the bevel gets thinner. Where there are hills and valleys in the blade face, the light will jump across or bend askew.
11-12-2012, 05:17 PM
What was the lowest angle you did apply?
The steel behind the edge is somewhat thinner where the bevel is larger. Hard to say from the pix whether it is an overgrind, or an unevenness that will disappear with a little thinning. Hope one of the pro sharpeners will give their comment.
PS one already did!
11-12-2012, 05:34 PM
10-12 degrees was the lowest-really my goal was to thin the bevel then apply a primary cutting edge. It's a 70/30 (Pic is of the 70 front side). it seemed regardless of angle the uneven bevel would exist. Perhaps I am applying to much pressure on the sides of the stone rather than in the middle?
11-12-2012, 05:37 PM
May be your stone is dished.
11-12-2012, 05:41 PM
I thought it was a possibility-although I started with a DMT extra coarse which is how it all started.
11-12-2012, 05:45 PM
I'd bet my dollars to your doughnuts that you're just seeing inaccuracies in the grind. Doesn't seem like anything worrisome, just hard to get a perfectly even bevel on an imperfectly ground knife.
11-12-2012, 05:49 PM
Only on one knife makes me think it could be a grind issue. I have a similar hiccup in my Misono gyuto. Mine only happens when thinning, there is a low spot (over grind) by the heal, so the edge is fine (for now).
I guess what I am saying is that it may not be your fault. And Welcome.
11-12-2012, 05:58 PM
You may verify with the magic marker trick at a very low angle. Use newspaper to not alter the finish.
If it's really an overgrind, the ink won't get abraded in the low spot area. That's a good reason for a return.
Powered by vBulletin® Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. All rights reserved.