Quantcast
Search Results - Kitchen Knife Forums

Search:

Type: Posts; User: PierreRodrigue

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    3
    Views
    127

    Thank you! Yes it was Hola! I found Hulu, but...

    Thank you! Yes it was Hola! I found Hulu, but that wasn't it, close though!! Thanks again.
  2. Replies
    3
    Views
    127

    US netflix in Canada?

    Guys, I has a program/app on my computer, which allowed me to view the US version of netflix. Some how, its now gone, and I cant remember what it was. It was free. Doing a search now, all I can seem...
  3. Replies
    26
    Views
    932

    For oven spring, timing is key, you need to catch...

    For oven spring, timing is key, you need to catch the rise before it peaks. I am fighting it also, but when I nail it, I have had what must be 20% spring.

    I have two books by Peter Reinhart, He...
  4. Replies
    17
    Views
    1,676

    This one is SPF

    This one is SPF
  5. Replies
    17
    Views
    1,676

    This one is 47 mm

    This one is 47 mm
  6. Replies
    17
    Views
    1,676

    As this one is a prototype, it is heavier. The...

    As this one is a prototype, it is heavier. The starting stock is 1/8" so heavier above the heel, but still a full distal taper, and a nice thin tip. Convexed blade faces to help alleviate stiction.
    ...
  7. Replies
    17
    Views
    1,676

    CPM 154 and DewCarta

    Hi guys, this is a 240 mm CPM154 Gyuto with Stainless welded/integral-ish bolsters.

    Blade is at HRC 61, ScotchBrite finish

    Scales are a new product called DewCarta. They have G10 liners, and...
  8. Replies
    7
    Views
    3,081

    O1 Gyuto with copper and sycamore

    I managed to steal a few hours this weekend when the boss wasn't looking... wrapped this one up. Work has been hectic to say the least.
    So as for the title, a 240 mm Gyuto.

    Blade is O1 @ HRC 61
    ...
  9. Replies
    101
    Views
    9,225

    Tom and I are still pushing ahead, ran into a...

    Tom and I are still pushing ahead, ran into a little hiccup, but not a deal breaker. It is still not to late to express interest.
  10. Replies
    9
    Views
    631

    I use acetone. Epoxy, clamp, wait a couple...

    I use acetone. Epoxy, clamp, wait a couple minutes, the wipe away the excess.
  11. Replies
    18
    Views
    897

    Its a steep learning curve, training will be a...

    Its a steep learning curve, training will be a solid three to four weeks, 10 hour days, then I settle into the rotation of 8 on 6 off. Looking forward to it. I'll text you when my new phone gets set...
  12. Replies
    18
    Views
    897

    Son, I hope the best for you. I'm glad you get a...

    Son, I hope the best for you. I'm glad you get a chance to make change. You deserve it.
  13. Replies
    101
    Views
    9,225

    It will all be done here.

    It will all be done here.
  14. Replies
    101
    Views
    9,225

    40 so far

    40 so far
  15. Replies
    101
    Views
    9,225

    ThEoRy was a tester, one of the staff in his...

    ThEoRy was a tester, one of the staff in his kitchen decided to trim some rubber of his shoe, when the knife was left out of hand momentarily. I believe Rick sorted him out! ;)

    It is designed to...
  16. Replies
    101
    Views
    9,225

    A bolsterless handle may be the simplest...

    A bolsterless handle may be the simplest solution. Tom and I will chat.
  17. Replies
    101
    Views
    9,225

    Paper micarta could be an option. It would be...

    Paper micarta could be an option. It would be bolsterless then.
  18. Replies
    101
    Views
    9,225

    The steel is a special smelt O1 we will be using,...

    The steel is a special smelt O1 we will be using, and chemically speaking, it will sit squarely between white 1, and blue 2. It is a very clean smelt, and will produce an excellent carbon steel knife.
  19. Replies
    101
    Views
    9,225

    Rick, $200 is still the target. Could be $225 but...

    Rick, $200 is still the target. Could be $225 but not likely.
  20. Replies
    101
    Views
    9,225

    Rodrigue McLean Lamson Production knife

    Hi everybody.

    First Tom and I would like to say thank you for everyone who has had input on this project, from a simple "I'm in" all the way up to the testers who graciously took their time to...
  21. Replies
    27
    Views
    662

    Happy Birthday young man!!

    Happy Birthday young man!!
  22. Replies
    463
    Views
    39,273

    So. I took the time to review all the posts, and...

    So. I took the time to review all the posts, and select some of the early discussions, as a review. I know it has been a long time since this has been on any ones mind. These quotes are a time line...
  23. Replies
    44
    Views
    13,833

    That sir, is best of show material! Outstanding.

    That sir, is best of show material! Outstanding.
  24. Replies
    20
    Views
    2,701

    Sand papers from 120 to 1000, then polishing. Not...

    Sand papers from 120 to 1000, then polishing. Not easy, lots of elbow grease... I think its worth it for some pieces. This one will find its home in a higher end restaurant, to be used for carving at...
  25. Replies
    20
    Views
    2,701

    CPM 154 Carving Set

    So here is a set I just finished polishing.

    Knife is a 270 mm, CPM 154, @HRC 61-62, mirror finished

    Fork is a stock removal piece from 1/4" stock, again CPM 154 @ HRC 60

    Tines on the fork...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4