Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20

Thread: Stone Fixer up for grabs

  1. #11
    Canada's Sharpest Lefty Lefty's Avatar
    Join Date
    Mar 2011
    Posts
    5,210
    I'm glad Mike got it. He's one of the most giving guys on the forum! Besides, I can't wait to see how a "Stone Fixer Handle" turns out.

    Cool gift, Mari!
    09/06

    Take a look around at: www.sharpandshinyshop.com

    Email me at: tmclean@sharpandshinyshop.com

  2. #12
    Senior Member Benuser's Avatar
    Join Date
    May 2011
    Location
    Amstelveen, The Netherlands
    Posts
    2,244
    Am looking forward to reading the review.

  3. #13
    Quote Originally Posted by Don Nguyen View Post
    Was there only one available for grabs? I'd be interested if you have other broken stuff...
    I actually have 2 more! LOL Since you asked first, you have dibs I guess? I will PM you in a moment.

    I'm not at work right now because I'm home with the stomach flu, but I will take a picture of them tomorrow and post.

  4. #14
    Senior Member Benuser's Avatar
    Join Date
    May 2011
    Location
    Amstelveen, The Netherlands
    Posts
    2,244
    Do you still have one left, Mari?

  5. #15
    Yup. Are you interested? Don has first pick but neither are that bad from what I remember. I'll be sure to send you guys a picture.

  6. #16
    Senior Member Benuser's Avatar
    Join Date
    May 2011
    Location
    Amstelveen, The Netherlands
    Posts
    2,244
    Quote Originally Posted by Korin_Mari View Post
    Yup. Are you interested? Don has first pick but neither are that bad from what I remember. I'll be sure to send you guys a picture.
    Sure, would be interested. And I promise writing a review.

  7. #17
    Quote Originally Posted by Benuser View Post
    Sure, would be interested. And I promise writing a review.
    Attachment 13945

    Is this stone okay? Please PM me if you would like it.

  8. #18
    Got it earlier this week.

    Small nick on the corner, but it's nothing to worry about. Overall I think the fixer works alright, but certainly has room for improvements.

    It works pretty slow, similar in speed to a fine DMT; little bit on the small side too. Most of the edges had a small ridge raised up, kind of like a burr. This would nick into the stones some times. I just took a DMT and beveled the edges, which didn't take long at all. It tends to load up with the slurry; this may be an issue if you worry about grit contamination between stones. Stays wet for a bit of time.

    However, it's only $20, and a pretty good fixer if you have a minimalist or basic setup. Bottom line is that it can work, but you may find it lacking if you've worked with diamond plates before. I think it works best on softer stones, as on somewhat harder stones it will go really slow (or not cut at all, if the stone is really hard. I remember Dave was talking about a stone that was really difficult to flatten unless if using a diamond plate).

    As I keep using it I will come back here to update if I notice anything else.

    Thanks for the opportunity Mari!

  9. #19
    Senior Member Benuser's Avatar
    Join Date
    May 2011
    Location
    Amstelveen, The Netherlands
    Posts
    2,244
    I've tried the stone fixer with Chosera 400, 800, 2k and 5k. The two lowest grits were very seriously neglected. I've no experience with diamond flatteners.
    After soaking both fixer and stone it went quite fast. Needed to keep it constantly wet, rinsed both fixer and stone frequently and interrupted the major operation on the 800 for a short new soaking.
    The ribbon profiled side is extremely effective when the lowest pressure is applied.
    Taking the initial soaking not into account, it took about 15 minutes to get rid of a 2mm height difference with the 800.
    On all stones, I like very much the final feeling the fixer left. Only the relatively soft 5k needed a few strokes with a nagura to get it smooth.
    I've noticed no contamination from the fixer to the stone. No contamination between stones either after simple rinsing of stone and fixer. As far as I noticed there is no reason for concern about remaining mud traces on the fixer.
    I think this fixer can be very useful for home users, especially if it is used with a new stone from the very beginning.
    I'm most grateful to Mari for offering this opportunity.

  10. #20
    Senior Member Benuser's Avatar
    Join Date
    May 2011
    Location
    Amstelveen, The Netherlands
    Posts
    2,244
    Update: whilst the fixer was great on relatively hard medium coarse and finer stones, I found a J300 that was totally immune to it. Please note that the Chosera grits I mentioned correspond to finer J-scale grits.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •