Quantcast
Enamel Dutch Oven - Page 2
Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20

Thread: Enamel Dutch Oven

  1. #11
    Senior Member
    mr drinky's Avatar
    Join Date
    Feb 2011
    Location
    St. Paul, MN
    Posts
    3,126
    Quote Originally Posted by Zwiefel View Post
    Right, I think it's rated 425/450F.

    Stainless looks nicer too.
    I didn't know it was rated that high, but I still would have replaced it so as to not worry about it.

    k.
    "There's only one thing I hate more than lying…skim milk, which is water that's lying about being milk." -- Ron Swanson

  2. #12
    All I can add is get out of the habit of tapping your spoons and tongs on the edge to clean them off.

  3. #13
    Senior Member
    mr drinky's Avatar
    Join Date
    Feb 2011
    Location
    St. Paul, MN
    Posts
    3,126
    Quote Originally Posted by Mike9 View Post
    All I can add is get out of the habit of tapping your spoons and tongs on the edge to clean them off.
    good tip.

    k.
    "There's only one thing I hate more than lying…skim milk, which is water that's lying about being milk." -- Ron Swanson

  4. #14
    Senior Member Miles's Avatar
    Join Date
    Mar 2011
    Location
    Deep in the heart of a Texas kitchen
    Posts
    522
    Quote Originally Posted by wenus2 View Post
    Jim,

    I strongly suggest this book: http://www.amazon.com/All-About-Brai.../dp/0393052303

    It gives a lot of good info on the science behind braising, dos and donts, general recipe composition, and several very good/great recipes.
    I've had the pleasure of working with Molly Stevens on a couple occasions. IMHO, her braising book is the gold standard where braising is concerned.

  5. #15

    Zwiefel's Avatar
    Join Date
    Jul 2012
    Location
    Little Rock, AR
    Posts
    2,369
    Quote Originally Posted by Mike9 View Post
    All I can add is get out of the habit of tapping your spoons and tongs on the edge to clean them off.
    wooden spoons seem to be ok...but definitely nothing hard. I've read that the Le Crueset have a clearcoat of enamel on the rim between the two enamel coats on the inside/outside and that it can be easily damaged...but I can't confirm either from the 4 pieces I've been using for the last 5 years. YMMV though.
    Remember: You're a unique individual...just like everybody else.

  6. #16
    Senior Member
    mr drinky's Avatar
    Join Date
    Feb 2011
    Location
    St. Paul, MN
    Posts
    3,126
    Quote Originally Posted by Miles View Post
    I've had the pleasure of working with Molly Stevens on a couple occasions. IMHO, her braising book is the gold standard where braising is concerned.
    I'm doing the braised oxtail from her book later this week. I also love her roasting book.

    k.
    "There's only one thing I hate more than lying…skim milk, which is water that's lying about being milk." -- Ron Swanson

  7. #17
    For what it's worth, fine steel wool (0000,000) will clean burnt-on food from a Le Creuset without scratching the finish. Brillo pads work too, but generic steel wool is cheaper.

  8. #18
    Quote Originally Posted by Zwiefel View Post
    wooden spoons seem to be ok...but definitely nothing hard.
    There's the rub see? I'm a creature of habit and don't differentiate between wood and metal when I'm rockin' out so I've had to get out of that habit altogether when using my enamel dutch ovens.

  9. #19

    Zwiefel's Avatar
    Join Date
    Jul 2012
    Location
    Little Rock, AR
    Posts
    2,369
    Quote Originally Posted by Mike9 View Post
    There's the rub see? I'm a creature of habit and don't differentiate between wood and metal when I'm rockin' out so I've had to get out of that habit altogether when using my enamel dutch ovens.
    I only keep non-stick safe stuff in my kitchen...everything else is for the grill. Even my kitchen tongs have silicon grips. For the exact reasons you mentioned, I'll get in a hurry and grab the wrong thing.
    Remember: You're a unique individual...just like everybody else.

  10. #20
    Senior Member
    Join Date
    Feb 2013
    Location
    bay area, california
    Posts
    553
    i've tapped various tools on the edge of my le cru. wooden spoons mostly, but the occasional metal tool. i cant tell if i have done any damage. i figure the edge will get "seasoned" anyways. if this beast cant handle a metal tool scraping, i dont want it...it is surviving the hell i put it thru so far. looks like krap..but still works great.

    i'll replace it one day with a new shiny one and relegate the old one for bread and deep fry duties..one day.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •