Quantcast
Time for a sping clean... and a Garasuki... i think...
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Time for a sping clean... and a Garasuki... i think...

  1. #1

    Time for a sping clean... and a Garasuki... i think...

    hi there. i just discovered this forum. nice to meet you all.

    i've always been into cooking, ever since i was a kid.

    i started collecting kitchen knives around 2006/2007 when a now ex-gf bought me a few global knives for christmas. i got a few more global knives, built up a bit of a collection, and used one of those mino sharpener things. and they were great - i always enjoyed cooking with them.

    then around 2010/2011 i found a couple of online cooking forums, read a bunch of stuff about knives, and bought a Masamoto VG. soon enough i'd replaced all the globals with Masamotos. and gave all-but-one of the globals to my mum.

    around 2011/2012 i bought some Wa-handle knifes - 3 x Konosuke and 1 x Ashi. but i rarely used them. they seemed too "special" and i was scared as heck to sharpen them in case i ruined them. also they had some small finishing issues with the handles where elements weren't flush which had always bugged me. so i used the Masamotos and started learning how to sharpen just using those Masamoto knives.

    anyway. today, having benefited from the advice of Japanese Knife Sharpening, i used some wet and dry sandpaper and re-finished the handles. and then i sharpened them. it took me a ridiculously long time. like 5 of 6 hours.

    they're now sat on my old cutting board while mineral oil slowly soaks into the handles...



    so now i think it's time for a spring clean. think i'm going to get rid of all the knives below (except the Mac bread knife), and just use the wa-handle knives above. i don't have the time to keep all of these sharp, and it seems silly to have doubles of so much stuff.



    does anyone think it would be a mistake to get rid of any of these?

    i could keep the 16mm drop-forged global and use it for cutting up meat when i'm worried about bones... but i was thinking it might be nice to get a 180mm Garasuki and use that instead.

    would anyone recommend a Garasuki as a good knife to have?

  2. #2
    Greetings! Nice transition so far, there will be people to offer advice as to the garasuki, I for one have never used one.

    Cheers!
    one man gathers what another man spills...

  3. #3

    Join Date
    Mar 2011
    Location
    The incredibly sophisticated Boise, ID <g>
    Posts
    907
    Welcome to the forums.

  4. #4
    Senior Member stevenStefano's Avatar
    Join Date
    May 2011
    Location
    Norn Iron
    Posts
    1,393
    You could put the old ones on the BST and see what you get or you could thin them and experiment with them perhaps, give them a new lease of life? If you're looking for a garasuki what kind of poultry do you eat a lot? Garasukis are pretty big, I used one for a while on 20kg turkeys and it worked awesome but on something smaller a honesuki would probably work better

  5. #5

  6. #6

    knyfeknerd's Avatar
    Join Date
    Feb 2012
    Location
    Charlotte, NC AKA The Queen City! The lint-filled belly button of the south.
    Posts
    2,679
    Welcome to KKF!
    I wouldn't recommend a Garasuki unless you prep a lot of large birds like gigantic chickens or turkeys or maybe Pterodactyls. I get a lot of use out of my Honesuki, but just don't see the need for a larger version.
    If you want to chop bones, get a big thick bone chopping cleaver. Or a German something...........
    If "Its" and "Buts" was candy and nuts, we'd all have a Merry Christmas
    -Cleon "Slammin'" Salmon

  7. #7
    thanks for the welcomes guys.

    does a Garasuki really feel a lot bigger than a Honesuki? i've not played with either of them, but they look real similar except one is 150mm and one is 180mm. i didnt think that 30mm would make a big difference?

    with my pettys i have a 150mm and a 210mm, but the 150 always feels a bit small. so i was thinking 180mm might be a nice length.

    to be honest i rarely break down whole chickens. i like roast chicken, so sometimes i need to trim the drum sticks so it looks pretty. i currently use kitchen scissors to do that.

    i often make stock. but i haven't needed to break down bones for that yet. i just use what i have, or whatever the butcher gives me, in whole pieces.

    i make a lot of stews and casseroles but there are rarely bones in the cuts of meat i work with.

    i would like to get into mincing my own beef and pork for ragu. feel like i'd need something a bit thicker than a Konosuke to do that... plus could be nice to slow cook bone in joints before breaking them down and mincing them.

    i cook a lot of thick steaks which need to be portioned before serving. haven't done them bone in yet, but would like to do that in the future.

    maybe i'd be better off with a Hankotsu and/or a cleaver... but i was kinda hoping the Garasuki would be able to do everything that those would do...

  8. #8
    Senior Member mpukas's Avatar
    Join Date
    Apr 2011
    Location
    Gyptuckey, CO
    Posts
    798
    Welcome! Honesuki/garasuki are pretty much only useful for poultry fabrication. If you're not breaking down birds on a regular basis, I don't think you have much need for one. Hankotsu is also primarily for meat fabrication, so again, unless you're getting whole primal slabs that need to be cleaned and trimmed, you don't have much need for one. If, however, you WANT one, by all means get one and have some fun with it. I do break down whole chickens quite often, and I get by just fine w/ a petty and beater Wustie. If you want to mince you own meat, get two sturdy Chinese cleavers.
    Shibui - simplicity devoid of unnecessary elements

  9. #9
    Senior Member stevenStefano's Avatar
    Join Date
    May 2011
    Location
    Norn Iron
    Posts
    1,393
    From reading your posts I'd probably avoid a garasuki, I think it's too specialised for your needs. Maybe just try a different gyuto if you're looking for a new knife to buy?

  10. #10
    Quote Originally Posted by ruscal View Post
    i would like to get into mincing my own beef and pork for ragu. feel like i'd need something a bit thicker than a Konosuke to do that...
    You don't.

    From your posts, it sounds like you are thinking the knife will be for chopping through bones? IMO you don't really need anything special for working around bones since you aren't chopping through them, just getting meat off them. I use a konosuke and scrape along bones at times and never had any problem with chipping. I do have a hankotsu since I like the shape and short blade when trimming meat, but its not a necessity IMO. A good petty is actually all I'd need.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •