Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Koa Split While Drilling

  1. #1

    Koa Split While Drilling

    Ran into a problem today. Koa (K&G stabilized) split right in the middle while I was drilling it. Never had wood split on me. When I look at the split, it's along the curl. When I put it in a vice and tighten, the split closes perfectly. Has anybody had a similar experience?

    It really suck because I am in the middle of the project that was to be completed for tomorrow. It makes even worse that I have no substitute block in stabilized koa.


    "If there’s something worth doing, it’s worth overdoing.” - An US saying.

    If my KKF Inbox is full (or not), please contact me via Email:

  2. #2
    Senior Member
    sachem allison's Avatar
    Join Date
    Aug 2011
    I haven't lived the life I wanted, just the lives I needed too at the time.

  3. #3
    Delbert Ealy's Avatar
    Join Date
    Feb 2011
    Indian River, MI Just under The Bridge
    I haven't had any stabilized wood split on me that I remember, but if it fits that close then glue it back together and proceed. The glue line should be minimal, and if you are using good glue it should be strong as well.

    Laminated metals specialist, Kitchen knife and gadget maker
    "Build a man a fire and he will be warm for a day, set a man on fire and he will be warm for the rest of his life"

  4. #4
    Senior Member
    Join Date
    Jan 2012
    San Francisco
    Probably a stupid question, but is your drill bit dull and/or are you adding too much pressure on it? This could cause the drill to act more like a "wedge" and cause the split.

  5. #5
    Quote Originally Posted by Marko Tsourkan View Post
    . It makes even worse that I have no substitute block in stabilized koa.

    I have a few if you're interested. Stabilized by K&G and ready to go.
    Please visit my store at Imagine the possibilities!
    Email me at
    Visit our Facebook page at
    All sales are backed with a no questions asked money back guarantee.

  6. #6
    Weird Wood Pusher Burl Source's Avatar
    Join Date
    Jun 2011
    Kerby, OR
    What you described can happen.
    Especially with really old growth or compression curl.
    Sometimes there can be hidden internal flaws.
    Dave saw that recently with a block of koa that looked good on the exterior.

    Not sure how you hold the wood when drilling,
    but if the wood is clamped to the table when drilling it can prevent slight movement that can cause the drill bit to wedge in the hole and break the wood.

    If the Koa was one of mine, let me know and I will mail a replacement piece.
    Mark Farley / Burl Source
    Phone 541-287-1029, Email
    Visit our web store

  7. #7
    Das HandleMeister apicius9's Avatar
    Join Date
    Feb 2011
    Honolulu, HI
    Happened to me with several woods before also. Usually I attributed it to too much pressure, dull bits, wrong drilling speed - or any combination of those.

    As for the re-gluing. I never used to do that with wood but in the end it's a resin-soaked material you are binding back together with resin. As long as the fit is perfect, I don't see any problem with that With other resin soaked materials like bakelite or reconstituted materials it works perfectly fine, just as with mammoth tooth which usually breaks and fits back together perfectly.


  8. #8
    Senior Member
    Join Date
    Feb 2011
    Just south of Charleston
    I've had decent luck with brad point drills. They tend to wander less, especially around knots in wood, which may cause less wedging/ stresses in the wood. Stuff always goes wrong when you're on a deadline. Good luck.

  9. #9
    Thanks guys.

    What took me aback is that I drilled a center hole and it went fine. The block split on me when I drilled an adjoining hole.

    I think I had 3-4 handles on this bit only, so it was still pretty sharp. I drill in increments, to clear the chips, so no unusual pressure or speed.

    All long drill bits wonder (or walk) a little bit, but I can't imagine them to wonder as much as to create a wedging pressure. In any event, this has never happened to me before and I have used this process for over 2 years now.

    I drill in a press with wood held by a vise.The vice jaws are about 1.5" tall.

    Here are the pics.

    Click image for larger version. 

Name:	DSC_0544.jpg 
Views:	18 
Size:	80.3 KB 
ID:	15448

    Click image for larger version. 

Name:	DSC_0545.jpg 
Views:	19 
Size:	66.8 KB 
ID:	15446

    Click image for larger version. 

Name:	DSC_0543.jpg 
Views:	15 
Size:	56.1 KB 
ID:	15447

    "If there’s something worth doing, it’s worth overdoing.” - An US saying.

    If my KKF Inbox is full (or not), please contact me via Email:

  10. #10
    Senior Member
    Join Date
    Mar 2011
    Cardiff, UK
    My guess would be internal stresses in the wood being released, haven't seen it as catastrophic as that before though. Quite often with natural woods i'll take a square block, make a tang slot and the block will have moved out of square by the time i'm done, guessing the stabilisation takes some of the ability to flex out so it cracked instead.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts