Quantcast
Sharpening wide bevel dbl bevel knives
+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Sharpening wide bevel dbl bevel knives

  1. #1
    mkriggen's Avatar
    Join Date
    Mar 2013
    Location
    Hawai'i
    Posts
    670

    Sharpening wide bevel dbl bevel knives

    Jon, I just went back through your sharpening videos and I think I might have been misinterpreting part of your technique. When you sharpen a wide bevel dbl bevel blade do you use the blade road as a guide for creating the actual cutting edge (like on a single bevel) or just for thinning?

    Mahalo,
    Mikey
    Available handles- http://s64.photobucket.com/user/mkri...able%20handles

    Rule #1- Don't sweat the small s%&t, rule #2- It's ALL small s%&t
    Mikey

  2. #2
    Sponsors
    JBroida's Avatar
    Join Date
    Feb 2011
    Location
    Beverly Hills, CA
    Posts
    4,037
    its a bit more complicated than that... you need to decide if you want a hamaguri edge or not. If not, the wide bevel is thinning, and you put a primary bevel on at whichever angle seems right for that knife and your preferences. If you are going ot use a hamaguri edge, then the wide bevel is both thinning and the primary cutting edge if that makes sense.

  3. #3
    Senior Member

    Join Date
    Feb 2011
    Location
    San Diego, CA
    Posts
    4,227
    Out of curiosity, what's most common? I tend to sharpen the large bevels pretty flat and then put a tiny bevel to form the cutting edge.

  4. #4
    Senior Member Brad Gibson's Avatar
    Join Date
    May 2013
    Location
    San Diego, CA
    Posts
    841
    I think about this when doing my takeda. It's sharp after doing the entire bevel but then I basically put a micro bevel on it and it lasts longer.
    "A recipe has no soul. You as the cook must bring soul to the recipe." -Thomas Keller

  5. #5
    Sponsors
    JBroida's Avatar
    Join Date
    Feb 2011
    Location
    Beverly Hills, CA
    Posts
    4,037
    common is tough to say... i think more inexperienced people tend to go for the former, whereas more experienced sharpeners and people with better knife skills tend to go for the latter

    (i also tend to use a microbevel when doing the wide bevel hamaguri sharpening... the edges tend to be super thin on knives like that)

  6. #6
    mkriggen's Avatar
    Join Date
    Mar 2013
    Location
    Hawai'i
    Posts
    670
    Ok, I had to look up "hamaguri", but I think I got it now. As always, thank you for your time and expertise.

    Be well,
    Mikey
    Available handles- http://s64.photobucket.com/user/mkri...able%20handles

    Rule #1- Don't sweat the small s%&t, rule #2- It's ALL small s%&t
    Mikey

  7. #7

  8. #8
    Senior Member ChiliPepper's Avatar
    Join Date
    Aug 2012
    Location
    New Zealand
    Posts
    169
    Hmmm, not sure if this is appropriate but I have a Yoshikane petty (hammered skd11 if that helps) that, to my eyes, has a uninterrupted "V" shape for three quarters of the blade geometry almost as it were two single bevel knives merged together, if that makes sense. I usually lay either side respectively flat on the stone to maintain the geometry and just put a microbevel at the end of the session, on one side. This cost me the kasumi finish but keeps the edge in top shape with almost no effort. Would that qualify as "hamaguri" ?

  9. #9
    Sponsors
    JBroida's Avatar
    Join Date
    Feb 2011
    Location
    Beverly Hills, CA
    Posts
    4,037
    not quite... imagine this kind of thing, but on both sides (and less of an angle change... i had to make it easy to understand in the picture, so i exaggerated it a bit)...

    Where the red and black meet would be the shinogi line (the top of your wide bevel)... where the green and red meet would be where you blend the two bevels together... and the blue would be a microbevel if you choose to use one. The angles arent really significantly different from each other in real life... its more about where and how you place pressure. If the difference in angles is 2-3 degrees, you're overdoing it. And for double bevels, this would be on both sides.

    Attachment 17735
    Click image for larger version

Name:	hamaguri angles.jpg
Views:	14
Size:	13.4 KB
ID:	17736

  10. #10
    Senior Member Seth's Avatar
    Join Date
    Feb 2011
    Location
    Philadelphia, PA
    Posts
    492
    Slightly OT: Jon, I have a number of shigs and they have monster size convexing on the bevels, including both single and double bevel knifes. I have often thought it was too much and I have starting very gradually flattening a bit. Has this been your experience and do you have an opinion about this?
    Thanks,
    Seth
    Everywhere you go, there you are.

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts