Quantcast
Takumi Ikeda 250mm AS Gyuto (My love affair with aogami super steel)
+ Reply to Thread
Results 1 to 7 of 7

Thread: Takumi Ikeda 250mm AS Gyuto (My love affair with aogami super steel)

  1. #1

    Join Date
    Mar 2014
    Posts
    6

    Takumi Ikeda 250mm AS Gyuto (My love affair with aogami super steel)

    Two weeks ago I purchased a much needed gyuto to put through the paces at work.

    I was looking for three things:
    Blue steel core
    Flat profile (k-sab, masamoto ks)
    Medium thickness with distal taper

    I decided to take a stab in the dark at a [relatively] unknown knife, the Takumi Ikeda 250mm AS Gyuto, from Mark at ThisSiteIsNotAllowedHere.

    I tried taking pictures of this beauty but my phone's camera is complete crap.
    The handle I received was the same one as the picture, bubinga with a wenge ferrule. The fit and finish on the handle was perfect. There were no rough edges or gaps and the tang is epoxied in with the machi completely covered. Both the spine and choil were rounded and polished.

    This is no thin knife by any means, coming out of the handle at 3.3mm then tapering to 2.4mm an inch in front of the heel then slowly tapering to 1.2mm 1 1/2" from the tip. The tip came incredibly thin, a little bit too thin. I ended up chipping it against the stainless sink when washing it (oops). Took me about 20 minutes to re-profile the tip and it came out just fine.

    The damascus cladding on this knife is NOT stainless. It appears that it's layered stainless with carbon which creates an amazing pattern when the carbon develops a patina and the stainless stays relatively stain-free.

    Lastly, I want to talk about the most important part of this knife, the Aogami Super core. It has a heat treating I'd estimate at about 63-64 HRC. The edge retention and sharpness of this steel is absolutely insane. I sharpened on a 1000 grit, then 6000 grit, then 6000 grit + newspaper strop. I have not resharpened after the initial sharpening 2 weeks ago, just some stropping on the 6k, then 6k + newspaper every couple days.

    Here is the list of the major stuff I prepped on a weekend with this knife

    10 Red onion, julienne
    14 Red pepper, julienne
    10 Yellow pepper, julienne
    10 Poblano, julienne
    8 Onion, brunoise
    2 Cabbage paper thin
    4 Red pepper paper thin julienne
    4 Yellow pepper paper thin julienne
    A **** ton of cilantro mincing and lime cutting

    20 lbs flank steak, sliced to about the size of the spine of this knife at the heel xD
    25 Chicken breasts, same slicing

    And I put this knife through this twice using only NSF poly boards.

    I noticed today that my hair was getting quite long. So instead of using my ****** hair cutting razor I decided to use this gyuto after some quick stropping on a 6k.
    Me with my haircut and the Ikeda.

    Just for shits and gigs I decided to see if this could still shave arm hair. Yes. Cleanly. Seriously. This steel is the real deal.
    I think I might be in love with this steel.

    I would seriously recommend picking this knife up if Mark has one available.

    Cheers.

  2. #2
    Senior Member
    Join Date
    Feb 2011
    Posts
    1,627
    Personally, I don't find the edge retention or sharpness that you described to be all that special.
    Michael
    "Don't you know who he is?"

  3. #3
    Senior Member
    Join Date
    Mar 2011
    Location
    Wales, UK
    Posts
    771
    Quote Originally Posted by Fritzel View Post
    T

    It appears that it's layered stainless with carbon which creates an amazing pattern when the carbon develops a patina and the stainless stays relatively stain-free.

    Really? I find this claim dubious.

    It has a heat treating I'd estimate at about 63-64 HRC.

    Do you have a RC tester? Or are you a bladesmith?


    I noticed today that my hair was getting quite long. So instead of using my ****** hair cutting razor I decided to use this gyuto after some quick stropping on a 6k.
    Me with my haircut and the Ikeda.

    Cool story bro, tell it again.

    So this knife is basically the most awesomest thing ever?

    Welcome to the forums.

  4. #4


    Dave Martell's Avatar
    Join Date
    Feb 2011
    Location
    Homeless, PA
    Posts
    9,475
    Hi Fritzel,
    I see in your profile that you have the following knives...

    Takumi Ikeda KS 250mm Gyuto
    Mac Santoku
    Victorinox beaters


    Besides the Ikeda (being reviewed here) you have what would be considered low performance knives. This might be one of the reasons why your review is so enthusiastic (glowing).

    It's not that members here won't believe that the Ikeda is a good knife, as surely it is, but many of us have seen new members (like yourself) come in here and give glowing reviews for CKTG products before and we've sort of become wary of this type of action. I'm sure that you're not a shill but your review could easily be seen as that type of thing by those of us who have seen this type of thing before.

    Welcome to KKF, try not to take any of this personally.

    Dave

  5. #5
    Senior Member
    Join Date
    Dec 2012
    Location
    charlotte, nc
    Posts
    1,271
    There's been quite a bit of hostile remarks toward posts from new members. If it seems like shilling, why not let the mods investigate and just ignore..

    Back on topic, can you put up some photos? I love AS steel btw.

  6. #6
    Senior Member turbochef422's Avatar
    Join Date
    May 2012
    Location
    New York
    Posts
    738
    I've actually herd it's a good performer, I think I'll pick one up myself. Thanks for the review. I'm in love with a 270 itinomonn gyuto at the moment though

  7. #7
    Senior Member bahamaroot's Avatar
    Join Date
    Jan 2013
    Posts
    582
    You guys sure do know how make a warm welcome.
    "Those who say it can't be done are always pasted by those doing it"

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts