Results 1 to 5 of 5

Thread: Personalization is available

  1. #1

    Join Date
    Apr 2012
    Location
    Plano, Tx
    Posts
    75

    Personalization is available

    Hey folks, we've been getting quite a few requests for personalization of cutting boards, so I wanted to let you all know that's an option. I'm actually in the process of buying a used laser now (gulp).

    We'll probably charge around $35 for this, and I expect most folks will use it for monogrammed initials or dates (wedding gifts etc). If it requires graphic arts time or if it's really large, that will cost more. There will be a learning curve for me, so we'll see how all this goes.

    There will undoubtedly be some technical questions about this, many of which I won't be qualified to answer. The laser basically burns into the end grain of the wood, creating a recess approximately 1/32" deep. The burning darkens the wood, and shows up best in maple, second best in cherry, and not great in walnut. I wouldn't recommend doing food prep/chopping right on top of an engraved surface, because that would require a little extra cleaning every time you use it and the chopping would eventually degrade the engraving. So if you get a board engraved, I'd recommend either choosing a corner of the board that won't be chopped on, or getting a reversible board with no feet and using one side for display and one side for chopping.

    We will be able to engrave logos, art, letters, numbers, etc. Copyrighted stuff will need official permission from copyright holder.

    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	personalized boardsmith.JPG 
Views:	66 
Size:	104.6 KB 
ID:	32624  
    John Loftis
    theboardsmith1@gmail.com
    cell: 469-387-8581

    www.theboardsmith.com

  2. #2
    Senior Member
    WildBoar's Avatar
    Join Date
    Feb 2011
    Location
    NoVa
    Posts
    3,358
    I think this is a great option. But for initials, etc. it may be better to put it on the edge (like the BoardSmith logo) for the reasons you state.

    __________
    David (WildBoar's Kitchen)

  3. #3

    Join Date
    Apr 2012
    Location
    Plano, Tx
    Posts
    75
    Quote Originally Posted by WildBoar View Post
    I think this is a great option. But for initials, etc. it may be better to put it on the edge (like the BoardSmith logo) for the reasons you state.
    Great idea! Unfortunately, the bed of the laser I'm buying doesn't drop down sufficiently to allow for edge engraving. I think this one has 6" of clearance. They do make models now that have a removable bed, allowing for engraving virtually any sized edge. But with the laser I'm getting, it's face or nada.
    John Loftis
    theboardsmith1@gmail.com
    cell: 469-387-8581

    www.theboardsmith.com

  4. #4

    Join Date
    Mar 2013
    Posts
    30
    John - If this is all you're going to do, I think a cheaper Chinese laser would be the better choice. Trotec, Epilog, and Universal are all MUCH better machines but if this is the only thing you're gonna do a mainstream Chinese laser will do it just fine. Do not buy that 40 watt "thing" you see on eBAy...please.

    Yes, figure out how to remove the bed and cook up a makeshift place to put the cutting board so you can engrave on the edge. Pretty easy I think!

    I'll send you an email with a picture of that trophy I made using one of your cutting boards. If you remember, I was going to inlay the board but I had to give up on that. My laser tube croaked after several attempts so I had to go with what I had. Thankfully, I realized the tube was dying before I tried to inlay it...again. Started with a 2 inch board and ended up just barely over an inch. That's a lot of sanding with the equipment I have on hand....

  5. #5

    Join Date
    Apr 2012
    Location
    Plano, Tx
    Posts
    75
    Quote Originally Posted by wilburh View Post
    John - If this is all you're going to do, I think a cheaper Chinese laser would be the better choice. Trotec, Epilog, and Universal are all MUCH better machines but if this is the only thing you're gonna do a mainstream Chinese laser will do it just fine. Do not buy that 40 watt "thing" you see on eBAy...please.

    Yes, figure out how to remove the bed and cook up a makeshift place to put the cutting board so you can engrave on the edge. Pretty easy I think!

    I'll send you an email with a picture of that trophy I made using one of your cutting boards. If you remember, I was going to inlay the board but I had to give up on that. My laser tube croaked after several attempts so I had to go with what I had. Thankfully, I realized the tube was dying before I tried to inlay it...again. Started with a 2 inch board and ended up just barely over an inch. That's a lot of sanding with the equipment I have on hand....
    Great thoughts. I ended up getting a used (10 year old) epilog 75 watt. The customer treated that thing like his baby-- as well he should have, since the invoice showed he paid $35k for it new. I did a test run and it all works, just need to learn the laser now.

    John Loftis
    theboardsmith1@gmail.com
    cell: 469-387-8581

    www.theboardsmith.com

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •