Quantcast
Length of a flat-grinding platen?
Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Length of a flat-grinding platen?

  1. #1

    Length of a flat-grinding platen?

    So I'm in the process of building a grinder for 50x2000 mm belts and I'm pretty free in designing the flat-grinding arm. What is a decent length for a platen?

    Thanks in advance

  2. #2

    Join Date
    Jul 2011
    Location
    St. Petersburg, FL
    Posts
    1,297
    Typically, they are 8-9 inches long depending on the grinder model. That would be 200mm minimum.

  3. #3
    I thought of making it around 250 mm since the steel I have is 500 mm and that would give me a spare platen. If there's a possible gain of going longer than 250 mm I'm all ears. The grinders I've used had all very different designs so I don't have first hand experience with the KMG clone I'm building.

  4. #4

    Join Date
    Jul 2011
    Location
    St. Petersburg, FL
    Posts
    1,297
    If you are using actual KMG measurements or parts, then I'm pretty sure that you want the 8 inch platen. Also remember to make the tooling arm longer than the regular KMG one. Your 2000mm belts are about 10% longer than the 72 inch belts that the American machine was designed for.
    Quote Originally Posted by Rottman View Post
    I thought of making it around 250 mm since the steel I have is 500 mm and that would give me a spare platen. If there's a possible gain of going longer than 250 mm I'm all ears. The grinders I've used had all very different designs so I don't have first hand experience with the KMG clone I'm building.

  5. #5
    The vast majority of grinding will be over a small area of the platen. I think this is the main reason people stick pyroceram fireplace glass to the steel plate to prevent wear. The length of the platen might help flatening the edge before grinding or flatening the spine. Maybe it could also be helpful for distal taper. It really depends on what other equipment you have for these type of things.

    I forgot to mention that platens cause significant drag, so the longer the more power you need.

  6. #6
    I made a 6" and a 10" platen out of 2"x1" 6061 t6 al. with a glass liner.

  7. #7

    Join Date
    Jul 2011
    Location
    St. Petersburg, FL
    Posts
    1,297
    Good point. On blades the size of the typical kitchen knife, you can grind lengthwise on a normal vertical platen without removing pieces of your fingers as long as it is not in intergral. Pyroceram or graphite/carbon fabric are good stuff but they do have certain disadvantages. Using either means that you can only use one side of the platen. With the plain steel platen typical on a KMG, you can use both sides and have two or even four different radii on the edges. Also, the edges of the pyroceram can get chipped out, so you need to be careful.
    Quote Originally Posted by David Metzger View Post
    The vast majority of grinding will be over a small area of the platen. I think this is the main reason people stick pyroceram fireplace glass to the steel plate to prevent wear. The length of the platen might help flatening the edge before grinding or flatening the spine. Maybe it could also be helpful for distal taper. It really depends on what other equipment you have for these type of things.

    I forgot to mention that platens cause significant drag, so the longer the more power you need.

  8. #8
    Quote Originally Posted by ******* View Post
    If you are using actual KMG measurements or parts, then I'm pretty sure that you want the 8 inch platen. Also remember to make the tooling arm longer than the regular KMG one. Your 2000mm belts are about 10% longer than the 72 inch belts that the American machine was designed for.
    I don't use KMG measurements, I'm using a KMG inspired plan from British Blades (for 1600-2000 mm belts) that I fit for my needs. Power will be 1.5 KW with VFD.

  9. #9
    i like the thought of the AL with the pyro glass face as the AL woudl wick more heat away from the platen then the steel one (yes i make mine way hot when grinding )

  10. #10
    Quote Originally Posted by l r harner View Post
    i like the thought of the AL with the pyro glass face as the AL woudl wick more heat away from the platen then the steel one (yes i make mine way hot when grinding )

    The heat reduction was my goal when I made them and it does run cooler then my old steel platen.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •