Quantcast
Bent blade - maybe?
+ Reply to Thread
Results 1 to 9 of 9

Thread: Bent blade - maybe?

  1. #1
    Senior Member
    Join Date
    Mar 2011
    Posts
    247

    Bent blade - maybe?

    So I'm a little worried my KS gyuto might be warped. When I place it right side down and press the heel flush with the surface, the tip is elevated by 1-2mm, starting right about where the blade curves up to the tip. Sighting down the blade, though, I can't see a bend, and placed left side down it's pretty much flat to the surface. Does anyone think I have anything to worry about? My thinking is that could be the result of an asymmetric grind, with more distal taper ground into the right hand face than the left. I do also sharpen it quite asymmetrically, which could contribute. If it is bent, is there much I could do without a heat treat cycle?

  2. #2
    Senior Member

    Join Date
    Feb 2011
    Location
    San Diego, CA
    Posts
    4,227
    If it doesn't bother you when you sharpen or cut, I wouldn't worry about it. A slight bend is pretty common. You can straighten straighten it but it won't be doing your blade any favors.

  3. #3
    Sponsors
    JBroida's Avatar
    Join Date
    Feb 2011
    Location
    Beverly Hills, CA
    Posts
    4,050
    fixing without heat treat cycling is a pretty common skill among knife makers and sharpeners in japan... bends will cause trouble with sharpening more than cutting

  4. #4
    Senior Member Benuser's Avatar
    Join Date
    May 2011
    Location
    Amstelveen, The Netherlands
    Posts
    2,056
    As you describe it, it's the distal taper and the convexity of the right side.

  5. #5
    Marko Tsourkan's Avatar
    Join Date
    Feb 2011
    Location
    Westchester, NY
    Posts
    4,092
    You can examine your blade to see if there is a bent. A good way to do it is to examine the edge under a bright light (bring edge to your eye level). You should see the warped section.

    The warpage won't affect cutting performance much, but when you sharpen your knife, you should be mindful of that spot.

    M


    "If there’s something worth doing, it’s worth overdoing.” - An US saying.

    If my KKF Inbox is full (or not), please contact me via Email: anvlts@gmail.com

  6. #6
    Senior Member Seth's Avatar
    Join Date
    Feb 2011
    Location
    Philadelphia, PA
    Posts
    496
    After looking at my ks, I agree with Benuser; you are probably seeing the combination of convexing, distal taper, sharpening. If you are sighting along the edge and it is straight, I don't think you have a bend.
    Everywhere you go, there you are.

  7. #7
    Marko Tsourkan's Avatar
    Join Date
    Feb 2011
    Location
    Westchester, NY
    Posts
    4,092
    I have a KS on hand. I will look at it and let you guys know.

    M


    "If there’s something worth doing, it’s worth overdoing.” - An US saying.

    If my KKF Inbox is full (or not), please contact me via Email: anvlts@gmail.com

  8. #8
    Senior Member
    Join Date
    Mar 2011
    Posts
    247
    Thanks everyone, that corroborates what I thought. I've only handled one KS besides my own, and I didn't think to compare the two when I had the chance.

  9. #9
    Marko Tsourkan's Avatar
    Join Date
    Feb 2011
    Location
    Westchester, NY
    Posts
    4,092
    Quote Originally Posted by dmccurtis View Post
    Thanks everyone, that corroborates what I thought. I've only handled one KS besides my own, and I didn't think to compare the two when I had the chance.
    So I took a detailed look at KS tonight and discovered an interesting thing - the distal taper is formed on the right side only, so as others have mentioned, the tip area will go up, when you press on the heel, when the knife is on the right side.

    I also took a good look at the edge - pretty darn straight. Overall, a good knife, though I think a little higher convex would have made it even better.

    M


    "If there’s something worth doing, it’s worth overdoing.” - An US saying.

    If my KKF Inbox is full (or not), please contact me via Email: anvlts@gmail.com

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts