Quantcast
Yoshihiro Honkasumi Deba 21cm
Page 1 of 3 123 LastLast
Results 1 to 10 of 26

Thread: Yoshihiro Honkasumi Deba 21cm

  1. #1

    Yoshihiro Honkasumi Deba 21cm






    The story started few years back, when I had a brief contact with deba. I dont even recall producer but it felt sooo cool.

    Then for some time the subject died, even though sometimes I nearly cried when had to fillet some redfish or salmon with that flexi shite or chefs knife.

    Situation changed now, when I started in company with great focus on quality, me myself are not really fond of way modern cuisine goes, I like the respect you can show the produce by taking the best out of it. Plus its quite possible I will be getting more into sushi.
    Plus of course amount of fresh fish available in Norway.


    Thats how I started to look around, didnt wanted to spend fortune, as usual, but wanted decent quality, I rather pay 50 extra and have less to straighten :

    And so after a talk to "the Jon", i bought 21o mm deba from yoshihiro.

    What was I expecting? More problems actually.
    What I wanted is straightness and even grind. And I cannot complain really.



    Blade

    Straightness 4/5

    Blades overally straight with just minor turning in the tang area.



    Grind 4/5

    Minor problems. Nothing that wouldnt get fixed with time.
    As usually i Started on my DMT. It always shows truth...
    The tip is too deeply ground off for my liking, the heel is too low hanging, there was also the overgrinds in the heel area of both iron and steel. [still visible]



    The other side is even with no bumps on the edge visible or any cavities, which could be encountered in Mizuno for example.
    Only small problem is the tip area, and Im not sure whether this is normal on new blade, or just a error. The tip bends to the steel side. Or was
    Because of that I had to grind little more of metal there just to allow the rest of bevel to get in contact with stone.


    It is still there, I will fix that over time.

    Sharpness 0/5

    I just mention that for those who would expect knife for that money to come any sharp.
    In my standard there was no edge on it completely, plus the primary bevel was at a pretty steep angle, changed already, in preparations for hamaguri.

    Sharpening 5/5
    Short, wide and heavy blade. Dream to sharpen, and a fast one.
    As I said, straightening of the secondary bevel took some time with DMT, but polishing and sharpening went quite fast. I didnt pay too much attention to the kasumi though. Why? Cause I know I will play with the blade for next few months.

    Now, Im not going to tell you how sharp this knife can get, or how sharp it got.
    Im not a fan of those silly-arse tests with tomatoes or paper.

    But the sharpness is quite nice after naturals.

    I havent got a chance to check the edge holding ability, but its looking good so far.

    Reactivity 5/5

    Which basically means, very good.
    I usually dont use a knife the same day I was sharpening, but even when I did, it didnt developed any patina after some fish prep.
    Also, after leaving for a while on wet stone, just tiny bits of discoloration showed up. And a few.

    Blades fit and finish 3/5

    Didnt expected more from it. It is OK with some brushing marks here and there. Spine rounded enough. Choil Area nice and clean, little to crispy, but at least polished.
    The front seems little rough.



    Handle 2/5
    This department doesnt matter nuttin to me, but I have to mention
    Maybe at Yoshihiro are thinking its good enough to give you piece of wood? And yes, I know you can get same in more expensive knives, but the horn have some overgrinds, is significantly smaller than wood. The wood as usual.
    Hole in the handle looks like the blade was alive when they mounted it in.





    So overally 4/5
    I think its worth all the money I paid for it for the amount of knife you get.
    And big thanks to JKI for being patient and pushing Yoshihiro into me. I was little affraid of it but I was totally wrong.




    And now the fun part. Experiments with wood this time...What happens when you vacuum knife in saya in linseed oil on highest program? Then bake in 50 for 100 minutes? And then dry in 50.








  2. #2
    Senior Member Crothcipt's Avatar
    Join Date
    Jan 2012
    Location
    wyoming, closer to nowhere than somewhere.
    Posts
    3,501
    wow love the finished product of the wood experiment. Excellent critique.

  3. #3
    Senior Member
    Join Date
    Dec 2011
    Location
    Sydney
    Posts
    1,147
    Looks like it is ready for fish now. This is the white steel one Jon carries, isn't it?

  4. #4
    Senior Member
    Join Date
    Oct 2011
    Location
    Salt Lake City
    Posts
    234
    I really like the linseed oil results. Great review and a good looking knife. I also recently bought a Yoshihiro gyuto and I've been very impressed with it.

  5. #5
    That is one impressive hunk of steel. I really love white #2.

    Did you add any mineral spirits to the oil? The first coat of tung usually requires cutting it with spirits or else it doesn't dry out and harden. Not sure about boiled linseed though.

    Thanks for the fabulous pics!

  6. #6
    Came some salmons today. 8 kilos each


  7. #7
    Senior Member zitangy's Avatar
    Join Date
    Apr 2011
    Location
    SIngapore
    Posts
    501
    Lucky devil.... Referring to the fish.....

  8. #8


    4x8kg

  9. #9
    you got some work to do there

  10. #10
    Nice, I love the cryovac'ed knife! Lets see some pics of the fish after you finished with the deba!

    I have a couple yoshihiros, not from Jon though, and I like them quite a bit. I believe mine are blue steel though. I would get more yoshihiros because I find it such good value, but I want to try out other makers to get a feel for everything.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •