Quantcast
Zombie Buschef Knife - Page 3
+ Reply to Thread
Page 3 of 6 FirstFirst 12345 ... LastLast
Results 21 to 30 of 55

Thread: Zombie Buschef Knife

  1. #21
    Das HandleMeister apicius9's Avatar
    Join Date
    Feb 2011
    Location
    Honolulu, HI
    Posts
    3,124
    Great thread. Reminds me of that Koster knife I had a while ago. Looked great, but was more like a Bowie than a real kitchen knife... Look forward to seeing where this is going.

    Stefan

  2. #22

    HHH Knives's Avatar
    Join Date
    Apr 2011
    Location
    Michigan
    Posts
    3,629
    It looks like tomorrow or Friday I will be Heat Treating this blade and a few others. Im not sure what I will do for the handle yet. But probably will do it up nice for ya is the blade hardens.

    Inspired by God, Forged by Fire, Tempered by Water, Grounded by Earth, Guided by the spirit.. Randy Haas

    240mm Stainless Gyuto!!

  3. #23
    Senior Member Crothcipt's Avatar
    Join Date
    Jan 2012
    Location
    wyoming, closer to nowhere than somewhere.
    Posts
    3,502
    Man you are busy, which is good to hear. Man I can't wait to see what you come up with. I usually don't get excited but this is blowing me away.

  4. #24
    Senior Member Crothcipt's Avatar
    Join Date
    Jan 2012
    Location
    wyoming, closer to nowhere than somewhere.
    Posts
    3,502
    Ok I am chomping at the bit to know how Heat Treating went. Did it melt all over the oven like I think it would? Pleas throw me a bone...

  5. #25

    HHH Knives's Avatar
    Join Date
    Apr 2011
    Location
    Michigan
    Posts
    3,629
    Hang in there. I didnt get a chance to HT the blade today. Im thinking tomorrow afternoon maybe.

    That is if it doesn't melt!!!

    Inspired by God, Forged by Fire, Tempered by Water, Grounded by Earth, Guided by the spirit.. Randy Haas

    240mm Stainless Gyuto!!

  6. #26

    HHH Knives's Avatar
    Join Date
    Apr 2011
    Location
    Michigan
    Posts
    3,629
    Today was the day. I started the HT process on this knife! First I had to anneal it and ran it through a couple of normalization cycles. Trying to make the steel as ready as possible for the quench!

    Believe it or not. HT went well. I took the blade up to temp, and held for about 5 minutes. Then quenched the blade in oil. And guess what, It didnt explode or delam or warp etc. seemed to HT well as far as I can tell at this point. And Is straight as a arrow.

    Its not in the first of 2 temper cycles..

    Here are a few pictures. I am working alone today. so I didnt get photos on the quench or clean up etc.
    Attached Thumbnails Attached Thumbnails Click image for larger version

Name:	IMG_7136.JPG‎
Views:	38
Size:	282.1 KB
ID:	5394   Click image for larger version

Name:	IMG_7147.jpg‎
Views:	35
Size:	22.7 KB
ID:	5397  

    Click image for larger version

Name:	IMG_7142.JPG‎
Views:	52
Size:	313.0 KB
ID:	5395   Click image for larger version

Name:	IMG_7146.JPG‎
Views:	47
Size:	339.7 KB
ID:	5396  


    Inspired by God, Forged by Fire, Tempered by Water, Grounded by Earth, Guided by the spirit.. Randy Haas

    240mm Stainless Gyuto!!

  7. #27
    Senior Member Crothcipt's Avatar
    Join Date
    Jan 2012
    Location
    wyoming, closer to nowhere than somewhere.
    Posts
    3,502
    wow. Just by how the metal acted, when I had it home I would have thought this would have been more of a problem than what it turned out to be. Thx for the pics.

  8. #28

    Join Date
    Jan 2012
    Location
    CT
    Posts
    470
    It's ALIVE!! Isn't think disproving the old idiom that you can't make a silk purse out of a sows ear??

  9. #29

    HHH Knives's Avatar
    Join Date
    Apr 2011
    Location
    Michigan
    Posts
    3,629
    Dont get ahead of me on this one guys.. It did make it through the quench.. And after its quenched I tempered it. and then I tested it for hardness.

    My initial tests are bad! Very low RC.. It is SO LOW that its softer then the test equipment that I use even goes.. I dont know what kind of steel they used.. but Its is not High Carbon steel, let alone 1095 like they claimed.. or I would of been able to get it to harden..


    Am I surprised. NO


    More to come later.

    Inspired by God, Forged by Fire, Tempered by Water, Grounded by Earth, Guided by the spirit.. Randy Haas

    240mm Stainless Gyuto!!

  10. #30

    Join Date
    Mar 2011
    Location
    Rockport, TX
    Posts
    4,892
    Could it be that it had a very small core of 1095, and that damascus cladding is made from low carbon stuff?

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts