Quantcast
Handle test to destruction
+ Reply to Thread
Results 1 to 10 of 10

Thread: Handle test to destruction

  1. #1

    RRLOVER's Avatar
    Join Date
    Mar 2011
    Location
    FIB
    Posts
    1,127

    Handle test to destruction

    I have tested a lot of my "failure" handles to see what kind of force it takes to break the epoxy butt joint,I have never tested how much heat they could take.I had to remove a Wa handle to regrind a blade so I took the opportunity to heat test the epoxy.So I wrapped the blade in a wet rag,clapped it in the vise and busted out the heat gun.I was expecting to just heat the wood up and slide the handle off the tang but that was not the case.I heated the wood up for a very long time slowly for 20 minutes,the wood was hot enough to burn me through a leather glove but the handle still did not come off.So I just kept heating the wood up for 10 more minutes until it was just about to catch fire and still the handle would not come off.In the end I had to cut off the chard chunk of wood(sorry mark) and had no true heat failure off the epoxy holding the tang in.

  2. #2
    Sponsors

    Bill Burke's Avatar
    Join Date
    Mar 2011
    Location
    Lives in the mountains near Boise, Idaho.
    Posts
    495
    What epoxy are you using Mario.

  3. #3
    Senior Member
    Join Date
    Mar 2011
    Location
    Gothenburg, Sweden
    Posts
    498
    I think i know where that knife is heading....

    Will that kind of heat not ruin the blade HT?

    Either way, i think different kinds of Epoxy is different in terms of heat sensitivity.

  4. #4
    Marko Tsourkan's Avatar
    Join Date
    Feb 2011
    Location
    Westchester, NY
    Posts
    4,092
    I had once horn end cap come off stabilized wood just from the movement, so since then I use hidden pins. An extra step, but you get a peace of mind.

    M


    "If there’s something worth doing, it’s worth overdoing.” - An US saying.

    If my KKF Inbox is full (or not), please contact me via Email: anvlts@gmail.com

  5. #5

    RRLOVER's Avatar
    Join Date
    Mar 2011
    Location
    FIB
    Posts
    1,127
    Quote Originally Posted by Bill Burke View Post
    What epoxy are you using Mario.
    I have been using system three T88

  6. #6

    RRLOVER's Avatar
    Join Date
    Mar 2011
    Location
    FIB
    Posts
    1,127
    Quote Originally Posted by RobinW View Post
    I think i know where that knife is heading....

    Will that kind of heat not ruin the blade HT?

    Either way, i think different kinds of Epoxy is different in terms of heat sensitivity.
    I wrapped the blade in a wet rag,the blade did not see any heat.Using a heat gun you can keep the heat in a small area.

  7. #7

    RRLOVER's Avatar
    Join Date
    Mar 2011
    Location
    FIB
    Posts
    1,127
    Quote Originally Posted by Marko Tsourkan View Post
    I had once horn end cap come off stabilized wood just from the movement, so since then I use hidden pins. An extra step, but you get a peace of mind.

    M

    The butt joint at the horn,spacer,and wood did fail which I expected to happen quickly being so thin.I was not expecting the handle to stay on.

  8. #8
    Most of the higher end epoxies fail around 500 degrees and higher.

  9. #9
    Mike Davis's Avatar
    Join Date
    May 2011
    Location
    Jackson, MI.
    Posts
    1,529
    That sucks Mario. That sure was beautiful. Good test information though, thanks for sharing

  10. #10
    Senior Member
    Join Date
    Mar 2011
    Location
    Gothenburg, Sweden
    Posts
    498
    Quote Originally Posted by RRLOVER View Post
    I wrapped the blade in a wet rag,the blade did not see any heat.Using a heat gun you can keep the heat in a small area.

    Glad to hear that!

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts