Removing wa handles

Kitchen Knife Forums

Help Support Kitchen Knife Forums:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

UglyJoe

Founding Member
Joined
Mar 1, 2011
Messages
426
Reaction score
1
Hey guys,

I'm thinking about refinishing my Mizuno and need to remove the handle to do so, and I had a question about it. I've seen Marko's instructions for this, and also one of maxim's video followed pretty much the same method. What I'm not sure of is how to tell the knife has been epoxied or not inside the tang. Marko said when this is the case you can't remove the handle without destroying it, which is obviously not something I want to do. Is there a way to tell if the handle has just been burned in vs. using epoxy as well? Or if it's been burned in is there no epoxy used, etc.? Anyone ever rehandle a Mizuno that knows if any epoxy was used or not?

Thanks,
UJ
 
If you are banging on it more then 90 seconds and it has not moved, I would say it is epoxied.I just pulled a watanabe off with three taps on the board.
 
Epoxy will soften if heated. According to System Three, their epoxy has a max service temp of 160º f., so a heat gun or heat lamp should soften it enough to remove the handle. It has a deflection modulus of 119º f., whatever that means!
If the handle comes off in pieces, well, that is another project, I guess!
 
What kind of knife is it?


270 Gyuto. Marko, when reinstalling the handle do you basically do something similar to maxim, kind of fill the tang hole up with bees wax and rub down the tang with it, then just tap it back on and let it set for a few hours?
 
my mizuno's handle wasn't epoxied, it was attached traditionally, but it was so tight that it has to be cut off.
 
Sigh.... not what I wanted to hear. Well, I'll give it a shot, and if it don't work, I'll think of something else.
 
Generally, Japanese makers seldom epoxy handles in. I have not come across a fully epoxied handle yet, even on Takeda, which has epoxy at the handle tip, but the tang hole is burned out.

To remove a handle, I use a wood mallet and a block of wood 4-6" longer than the blade (excluding handle). It takes me 4-5 strikes to remove a handle. I have done this countless times without a single failure. One day, I will get a camera and make a video of a process.

Joe - the trick is to place one end of the wood block against the handle and hit with a hammer hit the other end, while you holding a knife and a block in one hand and hammer in another. Put masking tape over the edge so you won't cut yourself and a rule of a thumb is to hold the blade with the edge away from your palm (I don't use masking tape). Hit hard and after 2-3 strikes you will start seeing movement in the handle.

M
 
Generally, Japanese makers seldom epoxy handles in. I have not come across a fully epoxied handle yet, even on Takeda, which has epoxy at the handle tip, but the tang hole is burned out.

To remove a handle, I use a wood mallet and a block of wood 4-6" longer than the blade (excluding handle). It takes me 4-5 strikes to remove a handle. I have done this countless times without a single failure. One day, I will get a camera and make a video of a process.

Joe - the trick is to place one end of the wood block against the handle and hit with a hammer hit the other end, while you holding a knife and a block in one hand and hammer in another. Put masking tape over the edge so you won't cut yourself and a rule of a thumb is to hold the blade with the edge away from your palm (I don't use masking tape). Hit hard and after 2-3 strikes you will start seeing movement in the handle.

M

I could be imagining this, but I'm almost certain that I saw some kind of video of this process recently. And it wasn't Maxim's video, I don't think...

Edit: Nope, not a video. It was Marko's thread with pics over at another forum. I don't think I should link there (or is that OK?), but here's a google link: http://www.google.com/search?aq=f&s...=1&bav=on.2,or.r_gc.r_pw.&fp=4d5c28f4960f9d04
Should be the first hit on google.
 
I could be imagining this, but I'm almost certain that I saw some kind of video of this process recently. And it wasn't Maxim's video, I don't think...

Edit: Nope, not a video. It was Marko's thread with pics over at another forum. I don't think I should link there (or is that OK?), but here's a google link: http://www.google.com/search?aq=f&s...=1&bav=on.2,or.r_gc.r_pw.&fp=4d5c28f4960f9d04
Should be the first hit on google.

I think Maxim uses the same technique. I prefer to use a wooden mallet for a stronger impact, but could use a hammer or another piece of wood that has some weight.

Highly recommend to put a tape over the edge. If you don't pay attention and hold improperly and a knife slips, you will get a nasty cut.

M
 
I could be imagining this, but I'm almost certain that I saw some kind of video of this process recently. And it wasn't Maxim's video, I don't think...

Would you have a link to Maxim's video? I don't think I have seen that. Work really does get in the way of keeping up with the forums these days...

Thanks,

Stefan
 
Would you have a link to Maxim's video? I don't think I have seen that. Work really does get in the way of keeping up with the forums these days...

Thanks,

Stefan

I am pretty sure it's in his Yoshi suji polishing video he posted recently.

M
 
Stefan, I have had to essentially destroy majority of the burned in Japanese handles, most of them were extremely tight, I think humidity expands the wood more than in a dry climate.
 
Stefan, I have had to essentially destroy majority of the burned in Japanese handles, most of them were extremely tight, I think humidity expands the wood more than in a dry climate.

I wonder if putting a knife in a freezer for a few hours might help this process? Would dry out the wood a little and should cause it to shrink back some...
 

Latest posts

Back
Top