Quantcast
Wood Sanding, finish
+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Wood Sanding, finish

  1. #1
    Sponsors
    maxim's Avatar
    Join Date
    Feb 2011
    Location
    Denmark
    Posts
    1,981

    Wood Sanding, finish

    What final grit of sandpapper do you use ??
    I have notised that stabilized wood will look plastik like when it is sanded up above 1k grit, maybe its just me
    But i like to finish them to max 800 grit.

    For Natural wood i feel comfortable with 1k and above but on stabilized it begin too look like imitated wood.
    What do you guys think ??

  2. #2
    Pabloz's Avatar
    Join Date
    Sep 2011
    Location
    Albuquerque, New Mexico
    Posts
    353
    I usually go to 2500 wet or dry on stabilized or natural. Stabilized I will then buff to a high gloss on the bufffer. On the natural woods I will usually finish with Tru-Oil (as many coats as necessary for any given wood) and then wax, hand buffed to a high glossy sheen.

  3. #3
    Senior Member
    Join Date
    Jun 2011
    Location
    Calgary Alberta Canada
    Posts
    50
    2000 wet/dry then power buff. I like em shiny.

  4. #4

    Join Date
    Feb 2011
    Location
    Salt Lake City, UT
    Posts
    2,327
    I like em to shine as well. I go 320,400,600,800 buff, Tru-oil and wax.

  5. #5
    Das HandleMeister apicius9's Avatar
    Join Date
    Feb 2011
    Location
    Honolulu, HI
    Posts
    3,246
    I am buffing with white compound and then lightly again with pink compund. I think I read that the white compound is approx. 1500grit equivalent, and I haven't noticed any big improvement if I sand beyond 1200grit in most stabilized woods. However, that changes with metal pieces, then I also go higher. Usually, I also apply some oil-based finish before buffing to bring out the colors better.

    For non-stabilized woods I vary a bit, depending on how oily the wood is. I used to apply a dozen layers of finish or more but have cut that back to less in most cases, trying to find a balance between giving the wood some protection but retaining some of the wood character.

    Especially with burl woods you sometimes find that even after stabilizing the wood still has micro voids or is not 100% smooth after sanding to 2000 grit and buffing. Unless there are deep voids or grooves, my personal preference is to take that as a character of the wood and leave it like that rather than slathering it in epoxy or CA glue for a smoother finish.

    Stefan

  6. #6

    Join Date
    Mar 2011
    Location
    Rockport, TX
    Posts
    4,892
    I agree that it can look and feel like plastic. I finish wood, currently, with brown paper bags. You may be surprised how fast it is.

  7. #7

    Twistington's Avatar
    Join Date
    Jul 2011
    Location
    Skelleftea, Sweden
    Posts
    478
    At the moment im toying around with ca-glue, 600>1200>2500grit and a sock loaded with a 3micron compound.
    -"we're gonna make gluten free lasagna"

  8. #8

    Join Date
    Apr 2011
    Location
    Oslo
    Posts
    1,428
    I dont bother higher up than 600. But I repeat that few times.

    Do you use damp cloth after each grit/round?

    After little buff by hand and ready steady go.

    But I aint no mass producer, just a pendehito [if you translate literally]

  9. #9

    Join Date
    Jan 2012
    Location
    CT
    Posts
    470
    I have sandpaper that goes to 12,000 grit (Micro Mesh), which is about a 4000-6000 grit US equivalent. If it's fully done, it will leave no scratches that are visible, but makes everything look like plastic. I bring the handles up to the 12,000 usually and look for scratches. Then I drop back down and bring it up to 400 or 600 US grit, and again look for scratches. I then go to the Micro Mesh starting at the 1500 and going to around 4000, then rub in a few coats of Tru Oil or Lin Speed oil. Then I check again for scratches and do a couple thin coats of either of those finishes, rubbing them in by hand. I prefer the wood to feel like wood, not plastic! I tried buffing the handles, but the wheels tended to make the burls look muddy and dished the wood in the softer areas, like on Spalted Maple Burl.

  10. #10
    Sponsors
    maxim's Avatar
    Join Date
    Feb 2011
    Location
    Denmark
    Posts
    1,981
    Thanks guys
    I usually finish with 1k or more but now i see that sometimes even 400 grit with some buffe looks very good and shinny.

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts