Quantcast
sharpness vs. keenness
Results 1 to 5 of 5

Thread: sharpness vs. keenness

  1. #1

    sharpness vs. keenness

    With knives I see a lot of misuse of some terms.

    On a properly sharpened knife, the edge under magnification will measure ~.4 microns across. (diameter) The edge of a knife will start to feel dull when it wears to ~1 micron in diameter.

    Sharpness is the measurement across the edge.

    Keenness is how fine the scratch pattern is on the sharpening bevel.

    Over sharpening is when the knife starts to become duller from incorect sharpening or too much stropping. If a little is good, a whole bunch is not better.

    Dullness is when an edge, because of wear, is greater than 1 micron.

    Knives can dull because of abrasive wear, adhesive wear, or corrosive wear.

    Hoss

  2. #2
    Senior Member Deckhand's Avatar
    Join Date
    Jan 2012
    Location
    Costa Mesa California
    Posts
    1,736
    TK hand one of your gyutos at the west coast get together. It was the only knife I wanted to keep picking up. You do amazing work.

  3. #3
    Senior Member Crothcipt's Avatar
    Join Date
    Jan 2012
    Location
    wyoming, closer to nowhere than somewhere.
    Posts
    3,501
    I think I am a culprit of this. I have noticed when stropping and not paying attention to what I am doing, like watching video, reading a forum, ect. I will notice some times that it feels worse. Never knew there was a keenness to compare to sharpness.
    Chewie's the man.

  4. #4
    Senior Member
    Join Date
    Jul 2011
    Location
    Melbourne
    Posts
    619
    Devin, I read this post this morning and have been thinking about on and off all day.

    I know that you've stated in the past that you think that many knife nuts over-sharpen their knives, in that regard you mean that their knives are overly 'keen', which leads to knives dulling faster.

    If sharpness is a quality of an edge determined by the width of the edge - substantially less than one micron - then surely it must benefit knives for them to be abraded with particles of one micron or less. i.e 8000+ grit stones. When in the past you have said that most knife nuts over sharpen, do you mean that they take their stone progression too far for the knives, or they spend too much time on each stone?

    I'm not disagreeing with you here, after reading some of your comments about over-sharpening, I've been aiming at far more aggressive edges for gyutos and petties with great results.

    Can you also talk about the difference between 'abrasive wear' and 'adhesive wear'?

    I'm curios about this, because of the idea that if you know how a certain knife will be used, different sharpening styles and techniques can affect performance. i.e slicing knives made of steel with large carbides will perform better with a less refined edge. Can that concept also be extended to edge retention? for example if I have a knife that will be used for certain tasks - push cutting veg and that's about it, is there an ideal balance of sharpness and keenness that will extend time between sharpenings?

    I'm going to go and sharpen a knife now.

  5. #5
    Senior Member
    Join Date
    Aug 2011
    Location
    Canoga Park, CA
    Posts
    143
    Quote Originally Posted by Deckhand View Post
    TK hand one of your gyutos at the west coast get together. It was the only knife I wanted to keep picking up. You do amazing work.
    +1. That and El Pescador's conversation about Hoss' knives. Moved Devin's knives WAY up on the list of lust-objects!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •