Quantcast
flattening stone advise
+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: flattening stone advise

  1. #1
    Senior Member
    Join Date
    May 2012
    Location
    Philippines
    Posts
    1,405

    flattening stone advise

    sorry for the noob question but i just want some advise on what i should get


    would this be good enough to use a flattening stone? or do i have to get an atoma 140? i don't really have a lot of sharpening stones but as everyone knows that a flattener is essential.

    http://www.amazon.com/DMT-WM8CX-DuoS...t+extra+coarse

    or something like JKI's diamond flattening plate would be okay too?

    would this last? most of my stones are 8 inches long so i was thinking of getting that or something longer like the 10inch version of the dmt.

    thanks.

  2. #2
    Senior Member

    Join Date
    Feb 2011
    Location
    Pensacola, FL, USA
    Posts
    3,813
    If you don't want to spend the cash on an Atoma, get this DMT, rather than the one you linked to:

    http://www.amazon.com/DMT-D8XX-Dia-S...403369&sr=1-10

  3. #3
    Senior Member
    Join Date
    May 2012
    Location
    Philippines
    Posts
    1,405
    would getting that be better than the duo version?

    i just thought the dimples would probably help with loading up with too much particles and get to have two usable sides (not necessarily as a flattener) instead of just one.

    but if you think it's better to get that one instead, i'll opt for it.

  4. #4
    Senior Member Chifunda's Avatar
    Join Date
    Jun 2011
    Posts
    322
    Most any advice I got from Rick, I would take.

  5. #5
    Senior Member

    Join Date
    Feb 2011
    Location
    Pensacola, FL, USA
    Posts
    3,813
    Quote Originally Posted by franzb69 View Post
    would getting that be better than the duo version?

    i just thought the dimples would probably help with loading up with too much particles and get to have two usable sides (not necessarily as a flattener) instead of just one.

    but if you think it's better to get that one instead, i'll opt for it.
    The mesh values of the plate you linked to is 60 Micron - 220 Grit (extra coarse) and 45 Micron - 325 Grit (coarse). The D8XX is 120 Micron - 120 Grit. For flattening, I would go with the larger mesh (lower grit value). I bought my D8XX almost four years ago on a recommendation on the 'old' forum (KF). It's still going strong today.

  6. #6
    Senior Member EdipisReks's Avatar
    Join Date
    Mar 2011
    Location
    Cincinnati, Oh
    Posts
    3,479
    i have both diasharp (in XC) and duosharp plates (C/F). they both work just fine. the coarser stones are faster, of course, but i like having a fine plate available. the diasharp doesn't seem to load any quicker than the duosharp, honestly.

  7. #7
    Senior Member
    Join Date
    May 2012
    Location
    Philippines
    Posts
    1,405
    thank you all for your inputs. will put them into consideration.

  8. #8
    Senior Member
    Join Date
    Sep 2012
    Location
    Seattle, WA USA
    Posts
    242
    Another vote for the Dia-Sharp plate. I have the XXC and it does as super job of stone flattening. I do it at the kitchen sink under running water, stone in one hand and the DMT plate in the other. It's hard to believe that the Atoma can do a better job but I haven't used one yet. Many people say it does, maybe someday.

  9. #9
    Senior Member
    Join Date
    May 2012
    Location
    Hawaii
    Posts
    1,268
    I've had my D8XX around 5 yrs. the 120 grit is good for leveling stones.You should keep it clean,now thanks to some tips here I use Bar Keepers Friend & a stiff fingernail brush,works great,then I set it out in the sun a little while to speed up the drying.

  10. #10
    Senior Member EdipisReks's Avatar
    Join Date
    Mar 2011
    Location
    Cincinnati, Oh
    Posts
    3,479
    Quote Originally Posted by keithsaltydog View Post
    I've had my D8XX around 5 yrs. the 120 grit is good for leveling stones.You should keep it clean,now thanks to some tips here I use Bar Keepers Friend & a stiff fingernail brush,works great,then I set it out in the sun a little while to speed up the drying.

    i use BKF on mine, too. i find that rusting carbon steel has a tendency to be transferred from my stones to the diamond plate, and BKF gets it off lickety-split.

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts