Massdrop for KKF?

[nakiriknaifuwaifu]

So it depends on how good gifts folks send you

Hah! Thanks in advance for the cleaver

 

[MarcelNL]

Gifts could help clearing customs in some countries...

 

[gregfisk]

Just make sure you don’t end up in jail.

 

[RDalman]

Next up handle installations

 

[Carl Kotte]

Next up handle installations

So vardagspolerat!

 

[RDalman]

So vardagspolerat!

PTV-fredag

 

[9fingeredknife]

HAHA, I see one very special handle in the mix...

 

[fritze]

Next up handle installations

Can´t wait to see those handles installed!
The knives will be awsome

 

[inferno]

Next up handle installations

helgpolerat högglansollon!

so who will get the "golden ollon edition" handle?? i bet that it will be a nice surprise

 

[RDalman]

helgpolerat högglansollon!

so who will get the "golden ollon edition" handle?? i bet that it will be a nice surprise

It depends on what was ordered

 

[tostadas]

Ok we can do more videos

This one looks like it got a little extra polish

 

[MarcelNL]

almost a wet look polish.

 

[inferno]

"weekday/everyday polish"

 

[tostadas]

Instead of using an electric carving knife with cheap stainless blades, would it be possible to attach some nice Dalman steel to a shakeweight? Or better yet, incorporate the motor into that polished custom wood?

 

[inferno]

Or better yet, incorporate the motor into that polished custom wood?

you mean like a concrete vibrator??

 

[RDalman]

you mean like a concrete vibrator??

Friday evening in europe is obvious.

 

[inferno]

party time!

 

[RDalman]

And if you get this from burnfitting, like some tar residue from smoke, that wipes off easy with alcohol. Sooner easier than later. I see some jknives sometimes with this left on the blades.

 

[fritze]

And if you get this from burnfitting, like some tar residue from smoke, that wipes off easy with alcohol. Sooner easier than later. I see some jknives sometimes with this left on the blades.

Thank you for showing us the creation of the knives step by step!
I really like your videos !

 

[gregfisk]

Thank you Robin, that was really informative and fun to watch. I’ve been using 30 minute slow set epoxy resin. I use the same procedure, without the torch of course. I’m going to give the hot glue a try. You don’t have to hold onto the knife for as long to wait for it to set and you can remove the handle if you ever need to. I enjoy watching a veteran like you doing your craft.

 

[ian]

And if you get this from burnfitting, like some tar residue from smoke, that wipes off easy with alcohol. Sooner easier than later. I see some jknives sometimes with this left on the blades.

That's a hot tang! I've always been afraid to make it that hot when installing. But I've never done a real burn in, just an install where I get the handle hot enough to melt the wax or glue... Inspiring.

 

[RDalman]

That's a hot tang! I've always been afraid to make it that hot when installing. But I've never done a real burn in, just an install where I get the handle hot enough to melt the wax or glue... Inspiring.

Yea i will admit that was a bit hotter than necessary, but works

 

[RDalman]

Thank you Robin, that was really informative and fun to watch. I’ve been using 30 minute slow set epoxy resin. I use the same procedure, without the torch of course. I’m going to give the hot glue a try. You don’t have to hold onto the knife for as long to wait for it to set and you can remove the handle if you ever need to. I enjoy watching a veteran like you doing your craft.

Hey I made my first knife about six years ago but thanks, good to hear it might help.

 

[ian]

Hey I made my first knife about six years ago but thanks, good to hear it might help.

Please tell me you were a corporate executive before that, or a copy editor for an advertising company. Btw, I heard someone call you the grandfather of Swedish knifemakers recently. It must be a young field!

 

[gregfisk]

Well, you’re a veteran to me and your knives are beautiful. I’ve only made maybe 10 or so knives in a little over a year. And I don’t sell any of them, just give them away. The videos are really enjoyable so thank you for that.

 

[Chopper88]

Hey I made my first knife about six years ago but thanks, good to hear it might help.

Seeing how sought after your knives are already, imagine how it will be when you're 78 and everyone's speculating on when the last Dalman will be forged

 

[RDalman]

Please tell me you were a corporate executive before that, or a copy editor for an advertising company. Btw, I heard someone call you the grandfather of Swedish knifemakers recently. It must be a young field!

I worked in a industry with quality control, checking practical function and tolerances to standards, for parts we built battery cabinets with.

 

[RockyBasel]

Great video Robin - love to see how the first mass-drop at KKF is coming together

 

[coffeelover191919]

When are these shipping?

 

[nakiriknaifuwaifu]

When are these shipping?

@RDalman, @RockyBasel and I are solidifying shipping plans and trying to find out what is best for everyone. After final costs are decided, then we will reply back with final costs and shipment dates.