SOLD 220mm Apex Ultra Go-Mai Gyuto

Kitchen Knife Forums

Help Support Kitchen Knife Forums:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

MSicardCutlery

Full-time Knifemaker-Canadian Mazaki
KKF Sponsor
Joined
Feb 28, 2022
Messages
1,912
Reaction score
5,572
Location
Canada
Hello All,


It feels like ages since I've made a new listing here. Here I have a nice gyuto to offer you all in Apex Ultra go-mai with a lovely bocote handle. I keep working to get my core thicknesses down as much as possible in san-mai and go-mai, little by little I'm getting better, I have the cladding running less than 1mm from the edge in places on this one, it scared me a little.

As a side note: everything seems reddish because of the large volume of smoke in the atmosphere from wildfires (thanks Quebec😝!) but I'm quite aways away from any of them where I live, especially the largest.
20230115_210139.jpg

20230115_210445.jpg

20230115_210537.jpg

20230115_210207.jpg

  • Blade: 222mmx56mm Apex Ultra(67-68 HRC) +15n20+low carbon go-mai, 1200 grit finish, etch and polish
  • Neck: 18mmx20mm
  • Handle: 134mm long, 22mmx26mm tapering to 18mmx22mm, bocote+peruvian walnut, oil finished and waxed
  • POB: 30mm from the hande
  • Spine: 4.39mm at the handle, 3.66 above the heel, 2.75mm at 12cm, .53mm 1cm from the tip
  • Grind: flat to convex, right hand bias, not quite zero ground
  • Weight: 193g
  • Relieved choil and spine
  • Edge: .15mm@1mm, .21mm@2mm, .48mm@5mm, .84mm@10mm Measured at the midpoint.
Asking $550 U.S + $25 U.S for shipping with insurance anywhere in North America. Overseas will be in the ballpark of $50-$75 U.S depending on the area.

Thanks for taking a look, and have a great day!

-Matt
 
Hello All,


It feels like ages since I've made a new listing here. Here I have a nice gyuto to offer you all in Apex Ultra go-mai with a lovely bocote handle. I keep working to get my core thicknesses down as much as possible in san-mai and go-mai, little by little I'm getting better, I have the cladding running less than 1mm from the edge in places on this one, it scared me a little.

As a side note: everything seems reddish because of the large volume of smoke in the atmosphere from wildfires (thanks Quebec😝!) but I'm quite aways away from any of them where I live, especially the largest.
View attachment 247536
View attachment 247537
View attachment 247538
View attachment 247539
  • Blade: 222mmx56mm Apex Ultra(67-68 HRC) +15n20+low carbon go-mai, 1200 grit finish, etch and polish
  • Neck: 18mmx20mm
  • Handle: 134mm long, 22mmx26mm tapering to 18mmx22mm, bocote+peruvian walnut, oil finished and waxed
  • POB: 30mm from the hande
  • Spine: 4.39mm at the handle, 3.66 above the heel, 2.75mm at 12cm, .53mm 1cm from the tip
  • Grind: flat to convex, right hand bias, not quite zero ground
  • Weight: 193g
  • Relieved choil and spine
  • Edge: .15mm@1mm, .21mm@2mm, .48mm@5mm, .84mm@10mm Measured at the midpoint.
Asking $550 U.S + $25 U.S for shipping with insurance anywhere in North America. Overseas will be in the ballpark of $50-$75 U.S depending on the area.

Thanks for taking a look, and have a great day!

-Matt
woow this is a nice one!! On 240mm would be great
 
Back
Top